Sign In
/
Register
Language
English
Deutsch
Française
Español
Português
Italia
Русский
日本語
한국어
简体中文
繁體中文
Please enter a full or partial manufacturer part number with a minimum of 3 letters or numbers
RFQ / BOM
0
Home
Products
Manufacturers
Memory
Discovery
News
Blogs
Q & A
Sample Application
Service
Quality Control
Delivery Information
Payment Information
FAQs
Return Policy
About Us
Home
> Q & A
All Categories
Recommend
Technology
MCU
Hardware design
EDA & PCB design
Applications
Development board
Original factory
Embedded
DIY maker
DSP technology
FPGA/CPLD
College area
Linux system
MCU application
STM32
MCS 51
MSP430 MCU
AVR MCU
PIC MCU
Circuit design
Power technology
Electronic Component
RF / ICT
Sensing control
EMC/EMI
PCB Technology / Design / Customization
Proteus simulation
Labview simulation
EDA circuit tool
Consumer Electronics
Auto electronics
Industrial Electronics
Other applications
Medical electronics
LED application
Raspberry Pi
Arduino
Bananapi
NanoPi
MicroPython
Seeed
Intel Development board
Linkit Smart 7688
Galileo/Edison
Freescale FRDM
Rayeager PX2
Waveshare
IntoRobot
Beaglebone Black
Firefly open source hardware
ZLG
Orange Pi
DFRobot
WRTnode
TigerBoard
Maxim technology
NXP technology
ON technology
WIZnet network technology
TI technology
ADI technology
Other original technology
Rohm technology
Cypress technology
EPSON technology
Rochester
TOSHIBA technology
LITEON technology
Micron technology
Preferred materials
Questions
Recommend
Latest
0
Reply
STM32SPI1 debugging runs at full speed without any waveform.
STM32
February 1, 2021
by Daley
57
0
Reply
STOP mode serial communication has a high bit error rate.
STM32
January 29, 2021
by Irena
75
0
Reply
How to configure the STM32F030SPI port?
STM32
January 14, 2021
by Chandler
81
0
Reply
STM32F030 has low power consumption and high current in stop mode.
STM32
January 5, 2021
by Caius
81
0
Reply
Can FSMC be used as external storage?
STM32
January 4, 2021
by Mercy
72
0
Reply
How does STM32F1CUBE use partial remapping?
STM32
December 24, 2020
by Diane
66
0
Reply
STM32 beginners.
STM32
December 22, 2020
by Nena
91
0
Reply
The stm32F449 test code compilation cycle is too long.
STM32F4
December 21, 2020
by Jina
100
0
Reply
STM32F103 cannot wake up when it enters STOP mode during interrupt.
STM32
December 21, 2020
by Gwyneth
83
0
Reply
The DAC channel of stm32 cannot be output.
STM32
December 17, 2020
by Lola
91
0
Reply
After the project based on stm32f103 is transplanted to stm32f051, the online hardware simulation stm32f051 program cannot run.
STM32
December 10, 2020
by Henrik
94
0
Reply
When the STM32F103RFT6 PC3 is used as an input, the PC3 mode is set to pull-up input. When the MCU reads out, the results are all high.
STM32
December 10, 2020
by Margo
89
0
Reply
When STM32F103C8T6 is doing three-resistance sampling, the interrupt enters two consecutive interrupts.
STM32
December 10, 2020
by Hakeem
77
0
Reply
STM32 does a dot matrix LCD program and the data area bursts, and I need to solve it.
LCD
December 3, 2020
by Franco
74
0
Reply
How does STM32F1CUBE use partial remapping?
STM32
December 2, 2020
by Bowen
94
0
Reply
stm32f4discovery audio acquisition and FFT calculation frequency is very large.
STM32
November 25, 2020
by Lennox
72
0
Reply
About the serial communication between STM32 and zigbee module.
STM32
November 25, 2020
by Miya
99
0
Reply
Stm32f427 replaces stm32f207 with 100 feet, and the serial port download jlink simulation encounters problems.
Stm32f427
November 24, 2020
by Kelli
89
0
Reply
The IO port of STM32F103 is connected to a 5V level. What if the IO port is used as a data port with both output and input?
STM32F103
November 19, 2020
by Arman
123
0
Reply
How do you deal with Error_Handler() in the HAL library of STM32?
STM32
November 19, 2020
by Yazmin
123
Ask Question
Hot Q&A
Do I have to use optocouplers to connect AD421 and MCU?
[Details]
What is the specific principle of adding two resistors and two transistors to the resistor step-down circuit in the figure?
[Details]
I want to ask why LM393 can't output low level?
[Details]
Causes and solutions for the leakage current of the tertiary tube?
[Details]
The single-chip PWM controls the field effect tube, and the power is turned on by mistake.
[Details]
May I ask how the MOS tube or optocoupler realizes the switch drive problem.
[Details]
What are the advantages and disadvantages of DCM compared with CCM PFC control?
[Details]
How to determine the size of the pad and the distance between the two rows of pads during PCB design?
[Details]
Hot Products
Select Your Location